familyname=Sapphire-R8245
manufacturer=Hornby
lowVersionID=10
highVersionID=10
definitionSource=JMRI
CV=2,"VstartVolt PartenzaV d�marr.Startspannung"
CV=3,"Acceleration RateAccellerazione (0-255)Accel�ration (0-255)Anfahrverz�gerung (0-255)"
CV=4,"Deceleration RateDecellerazione (1-255)D�c�l�ration (1-255)Bremszeit (1-255)"
CV=5,"VhighVolt Massimi (0-255):H�chstgeschwindigkeit"
CV=6,"VmidVolts intermedi (0-255)Vmittel (0-255)"
CV=7,"Manufacturer Version No: Versione Decoder: Version d�codeur: Decoder Version: "
CV=8,"Manufacturer ID: ID Costruttore: ID constructeur: Hersteller ID: "
CV=10,"EMF Feedback Cutout"
CV=28,"RailCom Address"
CV=28,"RailCom Data"
CV=28,"RailCom Command"
CV=29,","MultiFuncton","","Accessory",""Decoder Type"
CV=30,","OK","","NOK",""Motor short-circuit"
CV=30,","OK","","NOK",""Output 0-1 short-circuit"
CV=30,","OK","","NOK",""Output 2-3 short-circuit"
CV=33,"FL(f) controls output 1"
CV=33,"FL(f) controls output 2"
CV=33,"FL(f) controls output 3"
CV=33,"FL(f) controls output 4"
CV=34,"FL(r) controls output 1"
CV=34,"FL(r) controls output 2"
CV=34,"FL(r) controls output 3"
CV=34,"FL(r) controls output 4"
CV=35,"F1 controls output 1"
CV=35,"F1 controls output 2"
CV=35,"F1 controls output 3"
CV=35,"F1 controls output 4"
CV=36,"F2 controls output 1"
CV=36,"F2 controls output 2"
CV=36,"F2 controls output 3"
CV=36,"F2 controls output 4"
CV=50,"Clock - hours"
CV=51,"Clock - mins"
CV=52,"ABC activated"
CV=52,"ABC direction-dependency deactivated"
CV=52,"Activate push-pull operation with intermediate stop"
CV=53,"Intermediate stopping time"
CV=67,"Speed Table"
CV=105,"User Id #1"
CV=106,"User Id #2"
CV=111,"Signal Timeout"
CV=112,"Shunting Mode"
CV=113,","Steady","0","Strobe","1","Flicker","2","Flash","3"Light effect of function output 0"
CV=114,","Steady","0","Strobe","1","Flicker","2","Flash","3"Light effect of function output 1"
CV=115,","Steady","0","Strobe","1","Flicker","2","Flash","3"Light effect of function output 2"
CV=116,","Steady","0","Strobe","1","Flicker","2","Flash","3"Light effect of function output 3"
CV=117,"Dimming Value for Output 0"
CV=118,"Dimming Value for Output 1"
CV=119,"Dimming Value for Output 2"
CV=120,"Dimming Value for Output 3"
CV=121,"Delay time - hours"
CV=122,"Delay time - mins"
CV=123,"Delay time - secs"
CV=124,"Event 1 - speed"
CV=124,","Forward","0","Reverse","1"Event 1 - direction"
CV=125,"Event 1 - hours"
CV=126,"Event 1 - mins"
CV=127,"Event 1 - secs"
CV=128,"Event 2 - speed"
CV=128,","Forward","0","Reverse","1"Event 2 - direction"
CV=129,"Event 2 - hours"
CV=130,"Event 2 - mins"
CV=131,"Event 2 - secs"
CV=132,"Event 3 - speed"
CV=132,","Forward","0","Reverse","1"Event 3 - direction"
CV=133,"Event 3 - hours"
CV=134,"Event 3 - mins"
CV=135,"Event 3 - secs"
CV=136,"Event 4 - speed"
CV=136,","Forward","0","Reverse","1"Event 4 - direction"
CV=137,"Event 4 - hours"
CV=138,"Event 4 - mins"
CV=139,"Event 4 - secs"
CV=140,","None","0","E1","1","E1-2","2","E1-3","3","E1-4","4","E1-2 Repeat","10","E1-3 Repeat","11","E1-4 Repeat","12"Event Control"
CV=142,"Current Fuel or Coal"
CV=143,"Current Water"
CV=144,"Initial Fuel or Coal"
CV=145,"Initial Water"
CV=146,","Off","0","On","1"Simulation"
CV=146,","Off","0","On","1"Lights on empty"
CV=150,","Intrain V1.3","0","New PID","1","New PID tune for Lima","2"PID algorithm"
CV=894,"Current Fuel or Coal#2"
CV=895,"Current Water#2"
Reset delle CV ai valori di fabbricaHornbyRailCom ConfigurationBraking ConfigurationFault IndicationShunting Mode ConfigSignal Timeout ConfigurationDecoder clock (Ops Mode only)Hornby LightsHornby EventsAuto control Locomotive can start/stop based upon timer events,without input from the Command Station.Start timeEvent 1Event 2Event 3Event 4Hornby SimulationCoal/Fuel and Water for simulated use by locoSimulation Control