familyname=ESU SwitchPilot
manufacturer=Electronic Solutions Ulm GmbH
lowVersionID=0
highVersionID=254
definitionSource=JMRI
2016JMRIDaveHeapRonaldKuhn12016-12-05DGHCreated along with the Facade/capability support for programming22019-05-19RKadded german translation32019-12-04DGHAdded Bounce Effects and Secondary Address Warning42020-10-23DGH
                Swapped pane display order of Second Address Enable and Secondary Address
                to work around unresolved issue with splitVal and eumVal interaction,
                which causes CV value corruption with Read Sheets.
                Removed Secondary Address Warning.
            52020-11-16DGH
                Refactored to use new splitVal syntax.
            dccmotoroladccmotoroladccmotoroladccmotoroladccmotoroladccmotorolaOps Mode Accessory ProgrammingdecoderCV=1,9,""
CV=1,9,""
CV=1,9,""
CV=1,9,""
CV=1,9,"Primary Decoder AddressPrim�re DecoderadresseSets base address for primaryEinstellen der prim�ren Decoderadresse"
CV=35,36,""
CV=35,36,""
CV=35,36,""
CV=35,36,""
CV=36,"Enable Secondary AddressAktiviere zweite AdresseThis variable interacts badly with the Second Address Variables, also using CV 36 but different bitmasks.There is a warning on the Basic pane and a JMRI issue will be raised."
CV=35,36,"Secondary Decoder AddressZweite Decoderadresse"
CV=29,""
CV=29,"RailCom� EnableRailCom� aktiv"
CV=28,"RailCom� Plus Automatic AnnouncementRailCom� Plus automatische Anmeldung aktiv"
CV=28,"RailCom� Channel 2 Data TransmissionRailCom� Kanal 2 (Daten)"
CV=28,"RailCom� Channel 1 Command ConfirmationRailCom� Kanal 1 (Broadcast)"
CV=34,"Enable Zoom Function on Output 1Zoom Funktion an Ausgang 1"
CV=34,"Enable Zoom Function on Output 2Zoom Funktion an Ausgang 2"
CV=34,"Enable Zoom Function on Output 3Zoom Funktion an Ausgang 3"
CV=34,"Enable Zoom Function on Output 4Zoom Funktion an Ausgang 4"
CV=49,"Enable Relay 1 DelayRelais 1 verz�gert"
CV=49,"Enable Relay 2 DelayRelais 2 verz�gert"
CV=49,"Enable Relay 3 DelayRelais 3 verz�gert"
CV=49,"Enable Relay 4 DelayRelais 4 verz�gert"
CV=50,"Initial impulse only after command receivedServoimpuls nach empfangenem Kommando einschalten"
CV=50,"Timeout impulse after position reachedServo nach Erreichen der Endstellung abschalten"
CV=50,"Power on servo only while movingStromversorgung nur bei Bewegung anschalten"
CV=51,""
CV=51,""
CV=51,""
CV=51,""
CV=52,""
CV=52,""
CV=52,""
CV=52,""
CV=53,""
CV=53,""
CV=53,""
CV=53,""
CV=54,""
CV=54,""
CV=54,""
CV=54,""
Reset delle CV ai valori di fabbricaBasicB�sicBasicBasisZ�kladn�Output 1 AddressAusgang 1 AdresseOutput 2 AddressAusgang 2 AdresseOutput 3 AddressAusgang 3 AdresseOutput 4 AddressAusgang 4 AdresseServo 1 AddressServo 1 AdresseServo 2 AddressServo 2 AdresseServo 3 AddressServo 3 AdresseServo 4 AddressServo 4 AdresseServo 1 AddressServo 1 AdresseServo 2 AddressServo 2 AdresseServo 3 AddressServo 3 AdresseServo 4 AddressServo 4 AdresseServo 1 Address for position C and DServo 1 Adresse f�r Position C und DServo 2 Address for position C and DServo 2 Adresse f�r Position C und DServo 3 Address for position C and DServo 3 Adresse f�r Position C und DServo 4 Address for position C and DServo 4 Adresse f�r Position C und DID Costruttore (sola lettura)N�mero de fabricant (nom�ss lectura)Hersteller ID (nur lesen)ID &#269;�slo v�robce (pouze pro &#269;ten�)Numero versione del Decoder (sola lettura)N�mero de versi� del descodificador (nom�ss lectura)Dekoder Version (nur lesen)&#268;�slo verze dekod�ru (pouze pro &#269;ten�)Codice di prodotto del Decoder (se usato) (sola lettura)La refer�ncia del descodificador (nom�s si es fa servir) (nom�s lectura)Softwareversion des Dekoders (nur lesen)&#268;�slo v�robku dekod�ru (pokud je pou&#382;ito) (pouze pro &#269;ten�)AdvancedAvan�atAvanzatoErweitertAvanceretPokro&#269;il�RailCom� SettingsRailCom�RailCom� EinstellungenSend following information to the command station:Folgende Informationen an die Zentrale senden:Function SettingsFunktionseinstellungen"Zoom" Configuration"Zoom" KonfigurationRelay Control Settings (SwitchPilot Extension)Relais Einstellungen (SwitchPilot Extension)Servo ControlServo Einstellungen